Search results

Gauging intrest. I have Four Rockets tickets I am attempting to get rid of. They are section 116 row 15 at the Toyota Center. Jan 15th Rockets vs. 76ers.There are 4 total tickets and they come with a parking pass. I purchased them for $60.00 each but cannot go. I will let them go for $35 each...

I am headed out there. Feel free to stop by and chill if you want.

Does anyone want to come out tonight? It would be nice to get a few Mazda's out to represent.

I am selling my car and need a stock axle back exhaust. I am willing to trade my Mazdaspeed axleback for it. Even trade! Will send pics upon request.

There is a rubber piece right before the MAF on the filter side of the intake that has dried and is cracking. Where can I get a replacement?

Looking to buy a front and rear motor mount in good condition. No cracks etc. I have AWR front and rear that I will be taking off. Willing to work a deal. My location is Houston, Tx.

I have an apline cda 9855. The dash install kit I used originally is crap. What kit should I replace it with

I spotted you east of Austin on 290 Christmas day. Just wanted to say what's up and your car looks good at about 70 mph! I got a ticket going 83 about 5 minutes later...lol

Where is the best place to buy a new AEM cold air intake filter for my P5?

I have been having popping noises on the front right suspension on my car ('02 P5). I have been looking for the cause forever. Today, I found a round rubber black piece that goes on the outside of the sway bar bushing to be broken. The thin metal ring that surrounds it has broken and the...

Could a worn out side motor mount make a popping noise when my car goes over small bumps?

I noticed a while back that when the right front of my car hits a small bump or has any sort of movement, I hear a loud popping sound, or a creeking sound. I have had it to two reputable mechanics and they can't figure it out. Can anyone give me any ideas where to start? I have been under the...

Where is the best place to get an o2 sensor (the one between the motor and primary cat.)? I don't want to pay $200 if I don't have to.

Just wanted to know what you guys think of it. I personally didn't like the 3's as much as the Protege's until I saw the pics of the red MS3 on the front page of this site. Now im like (drool!)

First some background info. I have an 02P5 manual 5 speed with the original tranny still in it. The syncros are trashed and I have a Spec stage 3 clutch and Fidanza flywheel in it. After my motor swap I noticed tranny fluid on my driveway. From what I can tell tranny fluid is leaking into...

I have a VIS cf hood and it is getting cloudy. Do any of you know how to get this out? It appears to be just the top layer or so. Any advice on how to take care of this issue?

A friend of mine test drove and brought a MS6 by the house tonight. Check it out! Sorry bout the size of the pictures.

I just installed an Alpine cda 9855 deck, a set of focal polyglass 6.5 compontents, two 5.25 inch focal access series for the back doors, a jl 12w6v2 D4, a jl 500/1 amp and a 300\4 amp. Now for my question. If anyone has had any issues with any of this equipment could you please let me know...

Motor swap pics! For those of you who don't know, I waisted a crank bearing and had a short block rebuilt at a local performance machine shop. I didn't upgrade pistons, rods or anything like that. I'm not really planning on doing any performance mods anytime soon. First they hot-dipped the...

Saturday, I went to change my oil and there was only about 2.5 quarts left in the pan when I drained it. There are no signs of a leak anywhere around the motor. I put 4 new quarts in and now I've noticed a knock around 3000 rpm when I am driving or when I rev from 3000 to about 3500 or 4000 in...