Search results

My APEX 3" catless downpipe broke on friday at the track. Will be calling them tommorow to see what they can do for me.

Went to Island Dragway again today even with my broken downpipe. Only did 2 runs today and I'm very happy with the out come: 1st Run: 60'....2.348 330'...6.317 1/8....9566 1/8 MPH...75.50 1000'....12.366 1/4....14.744 1/4 MPH...94.39 2nd Run: 60'....2.227 330'...6.179...

Just got back from Island Dragway. It wasn't crowded at all. I got 12 runs in through the whole night. The average temp was 70 degrees with 100% humidity. Here are my best runs: 9th Run: 60'......2.357 330'....6.377 1/8.....9.658 1/8 MPH....75.09 1000'...12.470 1/4.....14.876 1/4...

I'm installing my Defi air/fuel ratio gauge and just need some help on what wire to tap into. I already have the illumination wire, ground wire, sender wire, and 12v constant wire hooked up. I just need to know where to tap into for the 12v ignition wire? I've been searching on the forum for...

APC Carbon Fiber Road Vision Sport Mirrors*Pics* Put my new mirrors on today. Excellent fit and finish.

I repainted some stuff in my engine bay. The engine cover, fuse box cover, battery tie-down, radiator brackets, and strut bar are painted with Dulpicolor Metalcast Yellow paint. Only things missing are a Optima Yellow Top and some hard pipes...can't wait for summer:D

I really like the look of this strut bar but its listed for the Protege 5, does anyone know if it will fit a MSP? http://www.jcwhitney.com/webapp/wcs/stores/servlet/ProductDisplay?catalogId=10102&storeId=10101&langId=-1&productId=274532&mediaCode=ZX&appId=227913

I just got done re-doing the clamps on my underbody lights and noticed a drop of oil on my drain plug. So I tried to tighten it but it was already tight. So oil is leaking out of my drain plug even though it is on tight. Anyone else have this problem?

Put the gauge in last night and finished wiring it this morning. My boost spikes to about 6.5 PSI then holds at 5.

I just got my Defi boost gauge from ARunto in the mail and I want to install it but I don't know what wire to tap into. I want the gauge to be wired so that it will light up when my parking lights are on. Does anyone know what wire I should tap into?

I just installed my dual gauge pod on my a pillar with the plastic screws that come with it. The only problem is that they don't fit over the metal support that is visible when you take the a pillar off. I took the support off so the a pillar could fit but I don't know if its safe to drive...

I was just wondering if the A Pillar Support was really needed or not. I just installed my dual gauge pod and it wont fit with the support because the support gets in the way of the plastic screws I used to mount the pod. Hers a pic: I NEED to know if this piece is neccessary to have on the...

Heres a pic of my StreetGlow Gold Series lights at night in the snow:

I like the way it looks and feels. I hate to say it, but it definitely feels a lot better than the stock one. The only thing i don't like is that the boot doesn't come up to the knob.

I got my StreetGlow lights the other day and went to install them and both the side tubes were broken so I sent them back and should have them back next week. I installed the switch and wired it up but I need help mounting the tubes. If anyone has any pics of where they installed their neons I...

Saw this on Ebay and thought it'd be nice to share: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2449643526&category=33630

I've decided to just replace the stock Kenwood sub in my MSP with another 8" sub. A lot of people seem to recommend the JL 8 W3v2. But i found this on Ebay: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3065364963&category=18802&rd=1 My question is, does anyone know if the Rockford sub...

I don't know that much about audio equipment so I wanted to ask some people who would know more than me. I want to get just a sub and box to replace my stock sub in my MSP and keep the stock Kenwood amp. My question is which sub and box combo would be better? Alpine Type R 12...

I really want to get some Tenzo seats for my car but I was just wondering if I NEED sliders or just the brackets? Any help would be great.

I just got back from Sansone where I made an appointment to get my car flashed on Thursday. Don said it would take like an hour. On the way back I saw a Blue MSP going south on the Garden State Parkway between exits 138 and 137. Just wondering if it was anyone on here? It was around 11:30...