Search results

Hello. Up for sale is a like new electronic oil pressure gauge kit including; 1. Gauge P/N 216EVOOP 2. 52mm Mounting Cup 3. Pressure sensor 4. 4-port Oil Filter adapter plate with an M20 thread adapter (Subaru, Nissan, Porsche, Honda, Sentra, Mitsubishi, Acura, Hyundai, Mazda) 5. Wiring 6...

Hey. Would anybody have a clue as to why this might be? The more throttle the harder it pulls to the right. This does NOT happen with the front tires in the air, so I don't think that the axles are at fault? The front end feels solid enough for it to not be the cause as well, however a...

Up for sale is my month old Galaxy SII Skyrocket (AT&T version). Not to be confused with the older model galaxy S2 with the slower processor and the smaller screen. It's rooted, CIQ-disabled (ATT's user tracker!) and is in better than new condition with the addition of invisible shielding...

No longer for sale!

Here's a video with an explanation of how this muffler works; Muffler was used for about 5k miles. I've removed the hanger and the weld marks. Good as new. "The Aero Turbine Series 2540i is a 2.5" i.d. inlet, 4" i.d. outlet with an angle-cut rolled tip. The 2540i was designed for any...

Up for sale is a set of CF eyelids. They stand to benefit from a refinish of the clear coating. There's a very small spider crack at the corner of the driver side eye lid as shown in the picture. $40shipped Thanks!

I know that there are plenty of how-tos on this subject, but I haven't seen any for the Sedan Protege with a mounting system I've devised. I think that my system is much stronger with better weight distribution for long term durability, as well as much easier projector alignment. I'd...

Up for sale is a new pair of Sedan headlights made by Spyder. $90 shipped! Save yourself a good chunk of change by buying mine. Thanks!

Hey. I have one Rear Right Illumina in perfect working condition. I had to reposition the endlink stud hole on the end link tab, however, for my needs. It's more forward than stock. $50 shipped! Thanks.

Looking for the above from any 2L manual protege in good condition! Thanks!

I was talking to a Mitsubishi Evolution 8 owner who's using an open source (free) tuning solution for his stock ecu which is capable of tuning every aspect of the computer. It makes sense that this combo could be adapted to any car just like any other stand alone ecu solution. It'll of course...

A normal male would be looking forward right about now. A gear head is looking down haha. My wife snapped this picture as I was busy examining that inline 6.

WRX injectors with about 60k miles on them and were in perfect working order when I pulled them. You'll be getting all of the needed seals, just drop them in and go! Here are pictures: http://www.mazdas247.com/members/Cus...2020.02.59.jpg http://www.mazdas247.com/members/Cus...2020.03.23.jpg...

Up for sale is the axle back portion of my previous exhaust for $125 shipped. Here's a video with an explanation of how this muffler works; Thanks!

Hey. I have an extra harness off of a 2002 Mazda 626. It's mostly complete, I think only a few plugs were cut. Could be used for a stand along ECU project or to replace individual sensor plugs on your existing harness. Looking for get $70 shipped. Thanks.

Install a fuel pressure regulator from a 2002 CA-spec'd emissions (might be the same as the federal spec'd or other years 626s) 626 FSDE, This brought my AFR down from ~12.3 to ~11.9 at redline on an otherwise stock tune and fuel injection system.

Up for sale is a custom 2.5" axle which should bolt up to the stock mid section piping on any sedan Protege. It tucks inside the bumper for a stealth look and produces a mellow rumble. Has some surface rust as can be seen in the pictures. Looking for $100. I'd prefer a local buyer. Thanks!

Hello. Up for sale is a high performance custom built (by Performance Techniques - http://turbocharged.com/main.htm) T3/T4 turbo using all Garrett internals including a 360deg. thrust bearing. There is 0 shaft play in any direction with oil circulation. It's a 50 trim with a .62 AR turbine...

Hey. Thinking of selling my forged engine (long block) with the following specs and issues; BLOCK Decked 8.5 CR Arias pistons K1 rods .020 over ARP Head studs ARP Main studs Polished crank Swaintech coated oil pump (Doc B Racing) HEAD Decked New valve seals Corksport Exhaust cam ISSUES; -...

Up for sale is a Unichip piggyback without the boost control solenoid which you can tune yourself!. It will work with any Protege, not just the MSP, if tuned for each individual setup. I'm including the USB cable and the DOS based software, manuals, base and CAI+Cat-back maps. It'll be...