Search results

  1. K

    TSB For Power Train Automatic Transmission Control Module?

    So I was bored and found a site that is a free VIN checker, decided to run my car and found a few TSB for my car! Reading through I saw this from 01-21-2004 "01-21-2004 103100 Power Train:automatic Transmission:control Module (tcm, Pcm) B28 and later pcm calibration update information repair...
  2. K

    Oil Pan "Sweating" Oil/leaking?

    Yea it was pretty bad, good thing I caught it in time. I knew the car was leaking pretty good but did not expect this! Lucky a rock didn't hit that corner and dump all my oil out on me! Got the new pan on and the new front pipe and all is good! Next thing to tackle is the timing belt.
  3. K

    Oil Pan "Sweating" Oil/leaking?

    Welp, found the problem, this is what happened when I lightly poked it with a screw driver. Seems the are a few pin holes in that area weeping oil.. https://imgur.com/zzuaYtq
  4. K

    Oil Pan "Sweating" Oil/leaking?

    So, has anyone had a problem where the oil pan weaping oil from excessive rust? I thought it was my drain bolt gasket, replaced it but still leaked. Thought okay, its the pan gasket, cleaned it up and the upper gasket area is dry but the lower pan is wet? So from what I can figure is the pan is...
  5. K

    Neutral Safety Switch Location?

    Does anyone know of the location of the neutral safety switch on a 2003 Mazda Protege DX with Automatic tranny? My car will not start in park sometimes and I have to put it in neutral, other times it is fine.
  6. K

    Top Left Valve Cover Bolt...Sheered

    So I ended up just drilling EVERYTHING out and made it a size bigger, went to Home Depot to get a new bolt, nut, and washer and here was the result. Pretty happy about how it went!
  7. K

    Top Left Valve Cover Bolt...Sheered

    So, I was inspecting my timing belt since I have 75k miles on the car now and upon removing the valve cover one of the bolts snapped clean off with the head.. I tried drilling it, snapped the bit, tried to drill the old bit out and no luck.. So I just put the cover back on without that bolt...
  8. K

    Purge Valve Hose Orientation?

    So when I tested it the top nipple of the solenoid would not hold vaccumm, but the bottom would hold? Does this mean it is bad or is this normal behavior of the valve since the bottom is the side that is getting sucked into the throttle body?
  9. K

    Purge Valve Hose Orientation?

    awesome thank you!
  10. K

    Purge Valve Hose Orientation?

    Can someone please tell me what hose connects to what port on the Purge Valve? 03 Protege. I took it off to test (was faulty) and forgot to mark what hose goes where...
  11. K

    Sputters After Fillup?

    Is that the one under the hood by the Intake Tube? If so I disconnected it and tested it and it seemed to work fine, I couldn't blow through it when it was off the car? Or is it the one by the charcoal canister under the car?
  12. K

    Timing Belt and Water Pump Replace?

    Never done a timing belt before, these cars pretty easy? Also RockAuto sells a timing component set. One is an Airtex and one is a DAYCO. It comes with waterpump, belt, tensioner, pulley, etc. What brand should I go with...
  13. K

    Timing Belt and Water Pump Replace?

    Hey all, I was wondering on what everyones take on replacing the timing belt and water pump on a 03 Protege DX 2.0 is. The car just hit 70,000 miles. I know Mazda recommends replacing it at 105,000 according to the owners manual, but does it matter that the car is 12 years old? Should I replace...
  14. K

    Sputters After Fillup?

    Sorry for taking forever, been very busy. It happens if I fill it half way, full, 5 bucks, 30 bucks. No matter what. Is there a way to check the purge solenoid? If i take it off it should not be able to blow threw right?
  15. K

    Sputters After Fillup?

    Hey guys should I replace the Purge Valve or the Vent Solenoid? This issue is present everytime i fill up
  16. K

    Protege Front Wheel Bearing Service - LOTS OF PICS

    would if i had the money lol i might just keep soaking it wth PB blaster every day before i drive it for a week and try again next week.
  17. K

    Protege Front Wheel Bearing Service - LOTS OF PICS

    I gave up on it.. i got everything off, axle nut, shock bolts, ball joint bolt, tie rod bolt, caliper bracket, then i got to the damn AXLE itself... this thing is so siezed into the hub i called it quits... i tried hammering with the nut on, pentatrating oil, air hammer, a puller that pushes on...
  18. K

    Protege Front Wheel Bearing Service - LOTS OF PICS

    Any way to do this without a bearing puller or a press? Was just gonna hammer in and out the bearings with a hammer and some sockets..
  19. K

    Sputters After Fillup?

    UPDATE: Car is now sputtering VERY badly at idle and stalls out if I do not give it any gas. Once the car is above 1,000ish RPM the problem clears, it is JUST idle... NO CEL's? I am stumped and frustrated...
  20. K

    Sputters After Fillup?

    My MPG is around 19-22 depending on my city/highyway mix
Back