VersaTuner - tuning software for Mazdas
VersaTuner - tuning software for Mazdas
Page 2 of 2 FirstFirst 12
Results 16 to 22 of 22

Thread: KMiata SCCA Solo XP swap

  1. #16
    High Speed Low Drag aMaff's Avatar
    muffled screams
    Protege5 & Protege FS Moderator

    1992 Miata / 2003 Pathfinder

    Join Date
    Sep 2005
    Location
    Lilburn, Ga
    Posts
    18,782
    I've got the oil pump swapped. RSX TypeS pump (compare it to the stock TSX monstrosity in my previous post):



    KMiata's billet oil pump housing to work with their oil pickup (to go over the steering rack). The stock TypeS pump pickup sticks straight back, which would go through the steering rack:



    Once I get the seal & gasket set in, I'll crack into the honda bond (needed for the 'oil squirter plug" bolt) and get the oil pan, water pump housing and timing covers back on. I'll need to grab a buddy this weekend to hold a wrench so I can torque the 50 degree intake pulley (vs the stock TSX 25 degree VVT pulley) onto the cam.
    ~Andrew
    Atlanta Region SCCA
    114 DP

  2. #17
    No words bazooka joe's Avatar
    Donated: $40
    Miata & NEMOC Moderator

    2016 Miata Club, 2004 MSM, 2014 CX5 Touring, Honda 1976 XL 175

    Join Date
    Oct 2002
    Location
    wbee ma to NC 2016 Jinba ittai
    Posts
    21,345
    Keeping coming....

  3. #18
    High Speed Low Drag aMaff's Avatar
    muffled screams
    Protege5 & Protege FS Moderator

    1992 Miata / 2003 Pathfinder

    Join Date
    Sep 2005
    Location
    Lilburn, Ga
    Posts
    18,782
    Steering rack's ready to go (minus a couple zip ties to secure the boots).
    New inner tie rods, new R Package outer tie rods, and my home-brew steering limiters.

    Sigs are visible only in your first post on a page. To change your thread display preferences, click here and enable 'Always Show Signature'.

  4. #19
    High Speed Low Drag aMaff's Avatar
    muffled screams
    Protege5 & Protege FS Moderator

    1992 Miata / 2003 Pathfinder

    Join Date
    Sep 2005
    Location
    Lilburn, Ga
    Posts
    18,782
    I thought I was done with the rack, until I had one of those "oh shit, you dumbass" realizations while drifting off to sleep last night.

    There is a shoulder on the new style Inner Tie Rod locking washers that goes on the OD of the rack, vs the old style washers that sat on the OD of the tie rod's threads.
    I realized the rack limiters I made are a really snug fit on the rack, and might not clear the washer. I pulled the boots off and turned the rack through its full range of motion and sure enough, I'd managed to reduce the total travel by another 1/4 turn or so (1/8" per side, give or take).



    I threw it in the lathe and put a counter-bore in it to clear the washer on 1 side, but still ride nice and snug on the rack:



    Much mo' better.




    Of course, taking those staked on washers off broke the areas that were staked, so I clocked them 90 degrees and had 2 fresh areas on the shoulder to put new stakes in. Those plus red loctite (again... removing the inner tie rods wasn't fun) should be good to go now.
    Sigs are visible only in your first post on a page. To change your thread display preferences, click here and enable 'Always Show Signature'.

  5. #20
    High Speed Low Drag aMaff's Avatar
    muffled screams
    Protege5 & Protege FS Moderator

    1992 Miata / 2003 Pathfinder

    Join Date
    Sep 2005
    Location
    Lilburn, Ga
    Posts
    18,782
    Not KMiata content as much as XP content, but these are currently being CNC'd

    Last edited by aMaff; 07-17-2019 at 09:31 AM.
    Sigs are visible only in your first post on a page. To change your thread display preferences, click here and enable 'Always Show Signature'.

  6. #21
    High Speed Low Drag aMaff's Avatar
    muffled screams
    Protege5 & Protege FS Moderator

    1992 Miata / 2003 Pathfinder

    Join Date
    Sep 2005
    Location
    Lilburn, Ga
    Posts
    18,782
    Picked up the Nine Lives Racing Big Wang this morning. Still waiting on the 2nd elements to come back in stock, but once they do that'll go on as well



    Last edited by aMaff; Yesterday at 12:18 PM.
    Sigs are visible only in your first post on a page. To change your thread display preferences, click here and enable 'Always Show Signature'.

  7. #22
    High Speed Low Drag aMaff's Avatar
    muffled screams
    Protege5 & Protege FS Moderator

    1992 Miata / 2003 Pathfinder

    Join Date
    Sep 2005
    Location
    Lilburn, Ga
    Posts
    18,782
    Finally starting to move in the right direction of putting stuff ONTO the motor vs taking stuff off. Water pump housing and oil pan are on.

    Last edited by aMaff; Yesterday at 11:21 PM.
    Sigs are visible only in your first post on a page. To change your thread display preferences, click here and enable 'Always Show Signature'.

Page 2 of 2 FirstFirst 12

Similar Threads

  1. SCCA Solo in Mississippi
    By bighoopty in forum Pics & Builds
    Replies: 0
    Last Post: 03-07-2010, 11:39 AM
  2. SCCA Solo II event on the 19th.
    By ls six in forum Global
    Replies: 0
    Last Post: 03-30-2009, 12:46 PM
  3. 2009 SCCA Solo Rules
    By fatti03msp in forum Pics & Builds
    Replies: 2
    Last Post: 01-31-2009, 06:24 PM
  4. Mazdas247 @ SCCA Solo II Nationals
    By xelderx in forum Pics & Builds
    Replies: 64
    Last Post: 10-16-2007, 04:17 PM
  5. SCCA Solo Nationals News
    By JDuncan in forum Pics & Builds
    Replies: 22
    Last Post: 10-06-2006, 07:45 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •