What have you done to your P5 today?
- Thread starter Tg5
- Start date
- :
- OPTION WAGON
I've been debating to the same lol
Jackie chan
Member
- :
- Pro5
Nooooo! And I need a new sticker soon if you're still doing it!
Sent from my SM-G900T using Tapatalk
- :
- Mazda protege5
Don't sell guys, mod!!
Sent From Papa Jays Phone
Sent From Papa Jays Phone
- :
- Mazda P5
I don't think there's much left to mod that evade hasn't done already.
My goal is to try and get the fsze running at full potential. That'd be nice.
My goal is to try and get the fsze running at full potential. That'd be nice.
- :
- Mazda protege5
Still its sad to see one go 
Sent From Papa Jays Phone
Sent From Papa Jays Phone
dorkidori_s13
Member
- :
- 2003 Mazda Protege5
just snagged a set of Advan Super Racing Gen 2s from Japan for my P5 Same wheels I have on my S13 hatch.... though a bit narrower!
Same wheels I have on my S13 hatch.... though a bit narrower!
SlowturboP5
Member
- :
- mazda protege5
Installed remanufactured left rear caliper and $8 pads. Also bled the brakes.
dorkidori_s13
Member
- :
- 2003 Mazda Protege5
Nothing super exciting, but my new mid section piping showed up today! Now I can get rid of that rusted out mid pipe that won't seal to the muffler properly! Just need to get a new catalytic converter section so I can have a nice new exhaust system! Thank raptor jesus for cheap ebay catbacks hahahhah
EDIT: New Corksport exhaust hangers just came in!!!
EDIT: New Corksport exhaust hangers just came in!!!
Last edited:
Replaced both rear struts today: Broke one on a speed bump yesterday. Yes, actually broke the hat on top of the strut, and the whole thing came up into the rear seat belt bracket. Drove home (slowly) like that and replaced both. This was an Edmonton car most of its life and lots o rust. Had to buy the 'quick struts' because needed the new top hats, cost me $700 for the pair with a discount! *Would have been $1000 without at Lordco, the only place with them* Then changed to my summers and did some other minor maintenance. Had to CUT the sway bar end link nuts off. That was a chore.
- :
- Mazda P5
Mazdaspeed door sills and Progress rear sway bar.
Waiting on Moog endlinks to top it off
Waiting on Moog endlinks to top it off
dorkidori_s13
Member
- :
- 2003 Mazda Protege5
just snagged an MP3 intake manifold for my P5 today! on the hunt for the matching ECU now... and JDM intake cam!
dorkidori_s13
Member
- :
- 2003 Mazda Protege5
eh, i dont really wanna make one... maybe ill do it one day.
EDIT: OK i cracked and made a built thread...
https://www.mazdas247.com/forum/showthread.php?123859689-My-P5-build-thread
EDIT: OK i cracked and made a built thread...
https://www.mazdas247.com/forum/showthread.php?123859689-My-P5-build-thread
Last edited:
dorkidori_s13
Member
- :
- 2003 Mazda Protege5
gotta love that brittle sun baked plastic
i pulled mine all off a while back since they were all busted up and cracked as it was. fortunately i have a good condition roof rack on the way eeeeeeeeeeeeeeeee!
i pulled mine all off a while back since they were all busted up and cracked as it was. fortunately i have a good condition roof rack on the way
eeeeeeeeeeeeeeeee!- :
- 2003 Mazdaspeed Protege 1660, 2004 Winning Blue RX8, 2005 Mazda6
I've completed the re-bearing of the bottom end of my P5- pump, bearings, front and rear seals. Three of the four mounts are installed. HVAC blower switch will be installed tonight. Transmission may get mated to the engine, but not sure yet.
I don't think I've ever posted in the P5 forum. At least not about my own cars.
I don't think I've ever posted in the P5 forum. At least not about my own cars.
