Search results

Like the title says I am planning to replace the brake booster since there is no pressure on the brake pedal. It just goes all the way down and it is not until it almost touches the bottom that the brakes apply. I am open for any suggestions you guys may have. Ok, the main questions is, is there...

Hello Everyone, I was wondering if anyone had ever installed a blow off valve on a Turbo CX 7. If so, I would like to get pointers on how to do this without causing any problems to the car.

Like the title says folks, does anyone know what is the part number or a good source to get the plastic clips that hold the side skirts in place. Also, a have a P5 that smokes during cold start and when I punch it. I did a compression test and it seems to be in good shape. I am thinking of...

So, I bought a rear caliper rebuild kit for one of my P5 a couple of weeks ago. I went ahead and rebuild it installed everything back and the bleed the brakes and everything is working fine. Now, this past week end I did the same with my other P5 but, this one did not turn out so well. I...

Like the title says, I just did the Seafoam treatment to my P5. Divided the bottle in three separate doses for the car, one part for the oil, one part for the gas tank and the rest on the brake booster line. As soon as I finished pouring into the vacuum line I quickly turned the car off. Waited...

like the title says folks, I am looking for the Oxygen sensor extension as I am trying to get my exhaust done and the cat will need to be relocated. PM if you have one.

Dear Members, I almost forgot to ask about the O2 Sensors on my P5 once I go turbo. At the moment I have two and the one for the wideband that I have not installed since I am replacing the exhaust which would make it three. When I replace the exhaust my cat will be relocated and I am afraid the...

can anyone tell me if the racing beat rear sway bar for Protg came with new and bigger sway bar brackets? I am having a difficult time finding one bracket for my P5 which has a racing beat rear sway bar.

Hi Guys, Just got my gauges in for the fuel/air ration and boost. I am looking for pointers on installation. I have never installed gauges so I figured I ask the community here. I am looking for the best way to get all of the power wires connected and where is the best place for the O2 that...

Hi there guys, I was wondering if anyone could tell me where is the best place to hook up the vacuum line for the wastegate and the BOV. Also, can someone tell me if this fitting works, http://www.atpturbo.com/mm5/merchant.mvc?Screen=PROD&Store_Code=TP&Product_Code=ATP-OIL-010&Category_Code=...

Hey guys, can some one tell me what fittings do I need to hook up the oil feed line to the back of the block. I am looking for a fitting where I can hook up the braided line and the oil pressure sensor, kind of like a tee. I seen them in the forum often but no part number or place to purchase...

Guys, My P5 is doing like a chirping noise and it is coming from the little ribbon that pushes on the Slave Cylinder. Once I touch the ribbon it stops. I also noticed that the clutch pedal is kind of soft. It has been like this ever since the clutch was replaced. As I am driving the car sounds...

Like the title says, I plugged the car and the code that comes up is P0300. I also have the check engine Light on and a blinking oil preasure light. I am seeing smoke coming out from between the fire wall and the engine. I am new to the MZ6 model can someone please help. !!!!!!

Does anyone know if the P5 J pipe is the same as the MSP J pipe?

I am looking to buy the Oil Feel line components that are compatible with the GT25R. I bought a set up on ebay that it was said to be for Protg Mazdaspeed and the stupid thing does not work. I can get the feed line to fit in the turbo's hole and fasten the dawm thing. If any one has any insight...

Does anyone know if the rear MSP calipers and brackets would fit the bolt pattern on the knuckle of my P5?

Hi Everyone, I have 98.9% of the parts to turbocharge my P5. Now I am going with the stock MSP setup which I have been told that if I have the MSP ECU should be just fine. However after posting on my local Mazdas FB page ppl tell me that I still have to tune the car or I will blow the engine. I...

Like the title says guys my wife's P5 grinds when shifting into third not if I double clutch it does not grind or if I keep it in neutral till the RPM drop it goes in smooth. It only does this when going into third no other gears give me a problem. Any thoughts?

So I recently found that my wife's P5 had a broken AC hose which caused the system to loose all of the Freon. I will be replacing the hose today thanks to my friend Neaspeed who was able to supply this hose. Now the question is, does anyone have a how to recharge the AC system at home type of...

like the title says I am ready to turbo one of my P5s. I am looking for generous ppl that are willing to lend a hand on this mod. I am from Reading, PA and have a small garage space to work on this. PM me if there are any Pennsylvanians close to me that have the knowledge and would like to chill...