Search results

Preferred new, but I'll consider used. PM me

I am about to install a used TSI turbo kit that did not include a downpipe. If you have a downpipe or any component of a 3" exhaust that will fit a T25 on a Protege5, PM me.

Not for A-pillar. I would like a steering column pod or gauge cluster bezel pod. PM me.

I just took these off my car, and they are in excellent condition. Wires and plugs are completely intact, bulbs are good, and there is no rust on the housings or brackets. One of the nuts is a bit rusty, but it still works fine. They have yellow Lamin-X on them, which I will leave on for you if...

PM me

This might be a long shot, but I am looking for some advice on OE-style endlinks. Since I installed my coilovers, my rear links are way too short and my sway bar is angled upwards. I'm looking for something around 8", but I would really prefer not to go with adjustable ones (bad experience in...

I just bought a lightly used MSP LSD (the revised version), and I am planning on having my local shop install it when they replace my clutch and CV axle. I know that the transmission case may require some grinding. Is this something that is within a normal shop's willingness? I just don't want...

Like the title says, these are Tein S-Tech springs mounted on Stagg SHS struts. The springs were purchased used a little less than a year ago, but they have no rust or blemishes. The struts were purchased new, and have been on the car as long as the springs have, since March of 2013. All...

PM me if you have some

Does anybody know of a decent shop in Greensboro, NC or surrounding area that can align a lowered car? I just got turned away from 2 different places because they couldn't fit my car on the rack. Not sure what my issue is beyond alignment though. I just installed coilovers so obviously there...

Does anybody know exactly what size the strut bolts are? I want to replace mine, but I don't want to get them from the dealer because they'd end up being like $70 for everything. I can't take one off and take it to the hardware store, because, well, I need my car to get there. Any help would be...

I am about to install some coilovers, but while I'm at it I would like to replace my rusty old bolts/nuts that hold the strut to the knuckles. Any idea where to find what size these are or where to find replacements?

Hi folks, I am about to buy some coilovers because I am stupid and want a harsh ride, so I could use some advice. Here is my question: how did you corner balance your car to make sure that you had your coilovers set up properly left to right and front to rear? I know that an improperly...

I know it's a long-shot, but I would like to buy a MSP front lip. PM me if you have one you want to sell.

What is your experience with different brands of mid-range coilovers (under $1,000)? My Racing Beat rear sway bar and clunk-fix brackets keep snapping the endlink mounting tabs off of my Stagg struts, so I am thinking of upgrading. I have been looking at Tokicos, but once I factor in the cost...

Hi folks, I am in need of a little advice. I just acquired some used GT Spec braces, and I am probably going to install them soon. I have a lower front tie bar and a rear reinforcement panel with v-brace arms. I understand that the front tie bar uses stock mounting hardware at factory mounting...

$160 shipped Besides some nicks and the missing paint where corrosion was sanded off, this piece is straight and true and functionally perfect (corrosion from the car body, to be precise. not the bar. aluminum won't rust. duh.). That being said, please don't bother low-balling me. I'm not even...

Get this hard-to-find suspension piece in nearly perfect condition! There are a couple of minor scuffs on the mounting plates, but otherwise it is pristine. $150 + actual shipping

How necessary are these? I am planning on installing some Mazda 6 front brakes tomorrow, but I just realized that I have an incomplete set of anti-rattle clips. I have heard some people say that you can go without them. Any thoughts?

Hi all, I just bought a set of MattV HID retrofit headlights from another user, but they are set up for a sedan and I have a P5. The wiring harness controller has a single plug that looks like it fits into an H4-style bulb holder (which makes sense because the sedan uses H4 bulbs). My question...