Search results

Well this is a TSB and my rear lip finally needs to be retaped. However the following part numbers are no longer stocked anywhere. 0000-8Y-C31 Tape rework kit I have some 3M double sided tape but it looks like Mazda used a thin special double sided tape, does anyone have experience with this...

Anyone here running SpeedBleeders? They don't have the MSP in the application list and i'm not sure what the stock bleeder size is for our calipers. If i remember correctly our front calipers don't have long bleeder screws like the SB7100 in the photo. http://www.speedbleeder.com/size.htm

It sounds cammed, it sounds cool... but!... it isn't right haha. The story is.. I installed my doc b oil system. This means, removal of the pan, mbsp, pump, timing belt, all belts etc. Also installed a custom 2.5" downpipe that is semi leaking at the flange to the mid-pipe which needs to be...

So i caught Gearz this morning with Stacy David and got inspired. I was going to do this before but it got me more motivated. After the F1 race I went outside, jacked up the MSP and started at it. Just a quick note, if you have access to a good welder, some steel and some basic fab skills you...

Hey guys can anyone give me some quick info on the upper rad hose?. I called the dealership and they wanted $114.04CAD for it. I almost fell off my damn chair and needed a change of underwear. Will the normal Protege hose work?. I know the rads are different and the return inlet is in a...

I only went on the Sunday but noticed you didn't end up completing Race #1 on Saturday. What happened? Will you be back for Round 3? Would love to take a closer look at that beast!

Hey everyone. Just installed the eibach pro kit yesterday and had no issues. However after a night I still have three fingers of rear wheel gap (more then stock). Everything was installed correctly. I know springs need time to settle but I'm freakin out a bit. Do I wait it out or give eibach a...

Hey guys, did some digging around but found nothing. Anyone know what hubcentric ring size I would need for the Kosei K1 onto the MSP hubs?. thanks!

Hey guys, looking to get some info. I really want to take the MSP on the track this season but nothing highly competitive just open track days for fun. I have heard or read the LSD SHOULD get welded before doing so. I am not out to kick the s*** out of the car just want a heads up before hand...

Ok guys I just finished my custom piping, relocated the maf.. added in a Greddy Type-RS. Start the car up.. sounds ok.. let it warm up for a few and rev it... no blow off.. i mean it is but its just air coming out of the bov.. then all of a sudden the idle went wonky when it got at running temp...

Ok i searched but couldn't find a straight answer to this question. I am in the process of doing hard pipes, relocating the MAF and adding a BOV. So from stock with the stock BPV there is a vacuum line that runs into it, I assume this is NOT the line to use to run to the BOV?. I saw some...

Hey guys, well it has warmed up around here and I think I may uncover the MSP and turn her over get her going. I have left it since winter and need to prime it before startup. I have read alot of guys do this if a turbo car has been sitting to get the oil through the system before startup. So...

My send/return oil lines to and from the turbo on my MSP are rusted and one of the fittings at the turbo is slowly dripping. I have a load of aircraft grade braided line sitting around here and need to know the proper length for each line, fittings on each end (Earl's?) and if I need to...

Hey guys.. driving around the other day I noticed.. 4.5 to 5 (peak) psi sounds a bit low to me. Shouldn't I be around 6 - 6.5psi?. If so, what are the usual problem spots for loosing boost.. vacuum lines?. No rough idle, or performance loss (other then what i see on the gauge).. it may have...

Just picked up a 93 GT and the ebrake cable is non existant or so i think.. i pull it up and its as loose as a goose. I went to the parts place and he said theres a front cable and a right rear or something. It's all wheel disc if anyone has any input. (ughdance)

Hey guys washing my car yesterday i found some lovely.. ohhhh lovely scratches where it looks like someone has dragged grocery bags or hand bags down the side near the driver's rear door. Funny thing is i park near nobody, not a soul so i tried blaming people in the house... didn't work. I know...

damn like my turbo is leaking noowww the exhaust. My question is, is the exhaust able to be purchased at any parts counter or do I have to go through Mazda considering it's Racing Beat. It's leaking in the rear section before the muffler

Ok so I have this sound coming from my rear.. does NOT happen on all bumps only some, now I just got my bushings replaced and the sound is still there, I looked at my end links they are fine. I don't know what the clunk sounds like but if i were to describe this sound, it's metal on metal but...

Looking for what's in the title. I will trade for my clears if anyone wants them. One has a chip out of it. These things are expensive at the dealership and I want to keep my asshole intact thanks. PM me, or e-mail me at vince@alienworx.com

Well the neighbour has a mazda 6 and he is having a mazda 6 club meet across the street from me and one of the guys is a customer service manager for Mazda Canada.. so I told him let me know i want to ask this guy about the production numbers for the MSP. He just came over here now and the...