BoostedSpd6's Build Thread

looks good boosted. Did you get any pics with the nightshades? I decided not to do it but im curious to see what it would look like.
 

BoostedSpd6

Nip Slip!
Contributor
V
MazdaSpeed 6
looks good boosted. Did you get any pics with the nightshades? I decided not to do it but im curious to see what it would look like.
ahh i posted it in the What have you done to your 6 today thread that i didnt like how it looked against the black mica at all.. so i stripped it all off, the lights actually look brand new now that i did that.. those pics are from today.
 

BoostedSpd6

Nip Slip!
Contributor
V
MazdaSpeed 6
6/24/2010 Update

Next up:

- Blow Thru MAF,Custom Intake

- A Huge Build!!! :)

and heres a few recent pics





 
Last edited:

zinger002

Needs Moar Bewst!
V
2006 Mazda Mazdaspeed6
still looks like poo without tint :p
the blacked out theme will not be complete untill tint is done.

other then that... (headbang)

hurry up and get that build done. (bowdown)
 

BoostedSpd6

Nip Slip!
Contributor
V
MazdaSpeed 6
still looks like poo without tint :p
the blacked out theme will not be complete untill tint is done.

other then that... (headbang)

hurry up and get that build done. (bowdown)
haha i know.. i do need tint.. write a letter to the RI State Department and have them change the tint laws.
 

zinger002

Needs Moar Bewst!
V
2006 Mazda Mazdaspeed6
i have the same tint laws in alberta, im think i have ~25% tint and i have yet to even be pulled over for it.
 

BoostedSpd6

Nip Slip!
Contributor
V
MazdaSpeed 6
just alittle update: :D and i also updated the first post alittle too.

~ Engine Tear down and Rebuild ( rods, pistons, ported head.. the whole shabang)
~ VHT Coating on Downpipe
~ Recoat Exhaust Manifold
~ EGR Delete
~ 4 inch Custom Intake/Inlet
~ Relocate Battery to Trunk

- Contacting HTC Racing and ZZ Powdercoating next week for
~ Powdercoated Engine Block (not sure if i can do the head)
~ Powdercoated Timing Chain Cover
~ Powdercoated Oil Pan
~ Powdercoated Transmission
~ Powdercoated Engine Mounts
~ Powdercoated Tranny Mounts
~ Recoat Valve Cover - Candy Blue
~ Powdercoated Wilwood Calipers - Candy Blue


- Calling CP-E next week about getting these
~ CP-E Fuel Pump
~ CP-E Triple Guage Pod
~ CP-E Standback
~ CP-E PNP
~ All CP-E Flashes
~ 3.25 inch MAF Housing

~ Turbonetics GTK-500 - Ordering next week
~ ACT Race Clutch/Flywheel Setup - Ordered July 8th 2010
~ Blow Through MAF Setup - Completed
~ Bigger Injectors Pending PTP Crowsfeet Problem and Injector seal issues - calling John next week as hes back from vacation
~ Rear Sway Bar - August
~ Adjustable Front Endlinks -August
~ GT-Spec Ladder Brace (if it fits, not sure with the corksport exhaust) - Contacted Ken about this
~ XtremeBoost Front Crash Bar - Calling Frank Next Week
~ Wilwood Big Brake kit (custom made) - August
~ SS Brake Lines - Ordered July 8th 2010
~ BC Coilovers - Ordering in August
~ Devils Own Stage 2 Meth Kit with 2.5 inch sump tank - Ordered July 9th 2010
~ DEI CryO2 Intercooler Spary Kit - Ordered July 9th 2010
 
Last edited:

BoostedSpd6

Nip Slip!
Contributor
V
MazdaSpeed 6
Build Progress

Update #1 7/12/2010 10:17am

-Tranny,Oil,Coolant are all drained at this point

- Hood, Downpipe, Manifold, Battery,Battery tray, Intake,Inlet, Intake Manifold,Intercooler Piping,OCC,Coolant Lines,TT Front Engine Mount,Front Bumper,Crash Bar, Strut Tower Bar,FI Grounding Kit are all removed from the car at this point, not to much more to go before i can pull it..
 

bazooka joe

No words
Moderator
Contributor
V
2016 Miata Club, 2014 CX5 Touring, Honda 1976 XL 175
Build Progress

Update #1 7/12/2010 10:17am

-Tranny,Oil,Coolant are all drained at this point

- Hood, Downpipe, Manifold, Battery,Battery tray, Intake,Inlet, Intake Manifold,Intercooler Piping,OCC,Coolant Lines,TT Front Engine Mount,Front Bumper,Crash Bar, Strut Tower Bar,FI Grounding Kit are all removed from the car at this point, not to much more to go before i can pull it..
weird, just with you yesterday driving your car and now it's all torn apart! can't wait to see the progress! keep us up to speed on the shop too!(2thumbs)
 

The ManLaw

The Manlaw of Want
V
'15 CX-5 Touring
ya know what would be cool during this tear down and rebuild? time lapse photography of the whole thing
 
V
2007 Mazdaspeed6 GT
if you have a blow thru setup, why are you calling cp-e about a 3.25" maf? going back to regular setup? if you stay blow-thru there is no point since the throttle body isn't that big.
 

mglavina

R3VO 3VOM
V
2006 Mazdaspeed 6
just alittle update: :D and i also updated the first post alittle too.
~ BC Coilovers - Ordering in August
Great choice on suspension ;).

Build looks like it's gunna be sweet, I agree with taking tones of pics along the way... Even taking a pic of the entire engine bay ripped apart would be cool.
 
Top