Search results

  1. B

    Protege Garage Intake manifold,sls midpipe

    -Protege garage intake manifold $120 shipped.SOLD -FSDE stock intake manifold low miles $70 shipped -SLS catless midpipe $120 shipped SOLD Open to offers. Having trouble loading pics of other parts on my phone.will do asap. Thanks
  2. B

    '91 626 starter on an FSDE?

    Has anyone tried the '91 626 2.2l engine starter for more torque on a high compression FSDE?
  3. B

    shorter brake master cylinder

    DOes anyone know of a shorter brake master cylinder that will bolt up to our cars?
  4. B

    SLS catless midpipe inner diameter

    Does anyone know the actual inner diameter of the SLS catless midpipe for the Protege?
  5. B

    Protege Garage Intake Manifold Plenum Opening Diameter?

    Does anyone know the exact Protege Garage Intake Manifold Plenum Opening Diameter?
  6. B

    2002.5 Mazda Protege 5 Fully Built N.A. - No Longer Available

    2002.5 Mazda Protege 5 Fully Built N.A. 2002.5 Mazda Protege 5 Mica Black,5 speed,Original Owner, No Rust, No Accidents,84,000 miles.Runs Strong. Never Raced, Built as a Project. - Fully tuneable Microtech LT 10s.standalone - AEM wideband - Autometer Oil Pressure Gauge ENGINE: - Integral Stg...
  7. B

    Protege 5 hood on a 2003.5 MSP

    will a protege 5 hood fit a Mazdaspeed Protege?
  8. B

    Microtech X4 external ignitor

    Anyone running a Microtech X4 ignitor with Direct fire or something similar here?
  9. B

    NEW 11:1 Wiseco Pistons/K-1 Longrod set (FSDE) - SOLD

    NEW 11:1 Wiseco Pistons/K-1 Longrod set (FSDE) 11:1 compression, custom (83.40 mm diameter oversize) forged Wiseco pistons with K-1 forged longrods, Wiseco rings/wristpins/clips included, brand new in the boxes. Intended for a high power NA build, or a Turbo build with moderate boost. Or if you...
  10. B

    NEW 11:1 Wiseco Pistons/K-1 Longrod set

    11:1 compression, custom (oversize) forged Wiseco pistons with K-1 forged longrods, Wiseco rings/wristpins/clips included, brand new in the boxes. Intended for a high power NA build, or a Turbo build with moderate boost. Or if you wanna run big nitrous and make BIG POWER these are what you need...
  11. B

    FSZE Starter

    Does anyone know where I can get an FSZE stater?
  12. B

    Higher performance starter.

    Does anyone know if there's a high performance starter for the FSDE, Ive got high compression and keep frying stock starters.
  13. B

    Injector Timing

    Anybody ever play with injector timing on a standalone?
  14. B

    High Performance Timing Belt

    Does anyone know if there's a high performance timing belt available for FSDE's? I keep finding chipping in 3 new belts I've installed. Has anyone else had this problem with timing belts, I've got a built NA motor that sees 7k RPM sometimes.
  15. B

    Microtech LT10s No Fuel

    It's an NA FSDE engine.Took the cam cover off, had to reshim lifters, was getting correct fueling and engine ran fine before.Now it cranks and the plugs/piston tops are bone dry. Tried 2 other previously good stored maps and ran a configuration check, could hear the plugs and fuel pump. Any Ideas?
  16. B

    WTB: FSDE Manual Trans Engine Wire Harness

    WTB: FSDE Manual Trans Engine Wire Harness
  17. B

    Microtech LT10s map gauge

    Does anyone know what it means when the laptop map gauge flashes red?
  18. B

    WTB;FSDE Engine Wiring Harness

    Does anyone have the Engine wiring harness for a manual trans FSDE they will sell?
  19. B

    Microtech LT10s ignition problem

    Had everything running great, went to start the car and it wouldn't fire. Pulled the plug with wires and ran a diagnostic of the computer and #4 wasn't firing. Anyone ever have a Microtech fry an ignition coil or related problem? The coils were new.
  20. B

    Intake valve size

    Does anyone know the stock diameter of the intake valve big end?