CorkSport.com is MAZDA PERFORMANCE!
CorkSport.com is MAZDA PERFORMANCE!

View Poll Results: How helpful was this post?

Voters
4. You may not vote on this poll
  • Helpful and explained very well

    3 75.00%
  • Helpful, but could be explained better

    1 25.00%
  • Explained well, but not helpful

    0 0%
  • Hard to understand and not helpful

    0 0%
Results 1 to 6 of 6

Thread: How-To: Replace A Mazda5 Headlamp Bulb (Low Beam)

  1. #1
    Registered Member

    Mazda 5, Mazda Tribute, & 1996 Miata MX-5

    Join Date
    Dec 2011
    Location
    Hopewell, NJ
    Posts
    4

    How-To: Replace A Mazda5 Headlamp Bulb (Low Beam)

    Mazda 5 Headlight Bulb Replacement (Low Beam)

    A. This is a frustrating job for most people because the opening in the back of the headlamp is too small for even small fingers, and it takes considerable force to release and re-tension the metal clip that holds the bulb in place. I've found a trick that makes this job a bit easier (it's still a challenge) and am sharing it in this post. The bulb is held in with a metal clip that is nearly impossible to re-clip by your bare hands. Therefore, fashion a tool to assist with the job from an 8” long flat spade screwdriver. Notch the screwdriver in the center of the blade so that the position of the end of the bulb retaining clip can be captured and manipulated into position. Photos are shown below of a screw driver modified with a notch, and a H7 replacement bulb:






    B. To remove the old bulb, do the following steps:
    1. Make space to work by removing any plastic covers in the vicinity of the back of the headlamp.
    2. Unplug the electrical socket from the back of the headlamp.



    3. Gently pry off the rubber boot on the back of the lamp that prevents water infiltration.



    4. Inspect how the bulb is held in place with the retaining clip so that you will know what it looks like when it is properly holding the bulb in position. Use the notched screwdriver to carefully release the bulb retaining clip, and swing it out so that the old bulb can be removed. The clip is too big for the opening in the back of the lamp to swing out without some twisting and manipulation of the end of the clip. With some effort it can be twisted clear of the opening. The photo shows the screw driver blade just prior to pushing and releasing the end of the retaining clip:



    5. Disconnect the bulb from the front of the H7 socket adapter and discard the old bulb.


    C. To install the new replacement bulb do the following steps:
    1. Wear surgical gloves for the following steps so that you don’t get natural oils from your hands all over the new bulb and reduce it’s life span.
    2. Attach the new H7 bulb into the H7 socket adapter and position this assembly into the back of the headlamp so that it fits. There is a stub on one side of the bulb socket that only allows the assembly to fit in snuggly one way.
    3. Swing the bulb retaining clip so that it begins to hold the bulb assembly in place. The clip is too big for the opening in the back of the lamp, so it will take some twisting and manipulation to get the clip inside the opening.
    4. With the bulb in position, and the clip inside the opening, use the notched screwdriver to push and hook the end of the clip into it’s final position. It takes considerable effort to push the clip in place.
    5. Apply some bulb grease around the inside flange of the rubber boot that keeps moisture out of the headlamp. Press the rubber boot onto the headlamp and back of the bulb socket.
    6. Press the socket back onto the connections for the bulb.
    7. Replace all the various plastic covers to complete the job!
    Last edited by CaptainCrunch; 12-16-2011 at 09:43 PM.

  2. #2
    Registered Member

    Mazda 5

    Join Date
    Jan 2012
    Location
    Kamloops
    Posts
    1
    Great info and pics, but I was confused when I looked at the replacement bulb and finally realized that the silver
    piece needed to be separated from the black plastic piece (socket adapter). I did this with a large flat bladed screwdriver. Up until I did this, I thought I had the wrong bulb.

  3. #3
    Registered Member

    Mazda 5, Mazda Tribute, & 1996 Miata MX-5

    Join Date
    Dec 2011
    Location
    Hopewell, NJ
    Posts
    4

    How the Bulb looks with and without the H7 Socket Adapter

    I realized after the job was done that I should have taken a picture of the new bulb next to the old bulb connected to the H7 socket adapter. It would have made it easier for others to see what to expect. But I wasn't about to undo the job after it was done. You are right that they look quite different when connected, and one might make the mistake of thinking that they had the wrong bulb. Your comment should help clarify it for others. Glad you figured that step (Section B, Step 5) out for yourself!

  4. #4
    Registered Member

    Mazda 5

    Join Date
    Sep 2011
    Location
    Vancouver
    Posts
    25
    I bought this based on someone else's advice.

    Tack Puller
    http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1

    Was able to swap out this very quickly. I did have to look quite closely at how the metal hinge is latched on (easier on the passenger side headlamp).

    I did find that there is a "right side up" on the seating. There is a little notch that fits in between two "posts". I noticed this only after one of the headlamps was shooting more to the ground than the other side. Second time unhinging the latch took two seconds with this tool!

  5. #5
    Registered Member

    Mazda 5, 2005

    Join Date
    Jan 2014
    Location
    Scripps Ranch, CA, USA
    Posts
    3
    Excellent thread. Thank you!

    Several points I'd like to make after just completing this job on both headlights:
    1) The tool described here was indispensable in making an impossible job actually possible to do. I cannibalized a duplicate small screw driver I had which was only 5" long. The narrower the head of the screw driver/tool, the better in my opinion. In this case, a smaller head is actually better since you are trying to get that tool into cramped spaces. The tools shown in this thread are on the big side of what I think makes the job easiest. Obviously, people were successful with the bigger tools.
    2) One fundamental problem with this design is that the long side of the wire-formed spring clip interferes with the round hard plastic housing. The long side of the wire-formed spring clip can be shortened by about 2 to 3 mm without impairing its function at all. I did this on both driver and passenger side clips with a dremel tool. It is quite easy to do with the spring clip in the unlatched and in the fully open position. This will make the job simpler next time. Before you un-clip the wire-form, look to see how much excess wire is on yours. Remove it to make the job a breeze next time. As long as that extra wire is there to interfere with the housing, the job is still a pain, even with the tool.
    3) The pictures in the service manual are not accurate in at least one respect. For example, the bottom right photo below shows the long side of the wire-formed spring clip flipped up while the short, opposite side is "down". That's bogus. Since it is one continuous clip, if one side is flipped up, the other side will be flipped up too. This was not initially obvious to me and was confusing, until I realized the documentation is just bad.


    4) On the passenger side, the job is easier if you unhook and set aside the power steering fluid reservoir. Pull straight up on it to unhook it.
    Last edited by All4fun; 01-03-2014 at 07:18 PM.

  6. #6
    Registered Member

    2003 Mazda Protege5

    Join Date
    Dec 2013
    Location
    Las Vegas, Nevada
    Posts
    15
    Last night I replaced the driver side headlight bulb on my 2003 Protege5. I bought a tack puller based on comments here but didn't really need it for that side; got it done with my fingers.

    The new bulb is noticeably brighter than the old one, so I figured I'd replace the passenger side one too. Not nearly as easy!

    In all the fiddling around trying to get the spring back in its locked position, the whole wire popped out from whatever holds it in place. I can't begin to see what was holding it in place before (something broke, I'm guessing). For the moment I put the new bulb in and it is held in place by the rubber seal.

    Talk about a simple job being frustrating! When I settle down a bit I'll go back and try to figure out how to get that spring back in place.

    For the moment, the rubber boot/seal seems to be holding the bulb in place fine. Somewhere else on the Internet I found a comment from someone that broke the clip(s) and the rubber seals have been holding things in place fine for over 2 years, so maybe I won't worry about it.


    Eric
    Last edited by ehsande; 01-30-2014 at 11:27 AM.

Similar Threads

  1. HID Headlamp Ballast Replace
    By sea91ray in forum Mazda3 Lounge & Welcome Area
    Replies: 1
    Last Post: 04-25-2013, 11:25 PM
  2. Low beam headlamp aim?
    By ckfreeman20 in forum Mazda3 Accessories & Appearance
    Replies: 3
    Last Post: 04-10-2011, 09:42 PM
  3. 2009 Mazda5 Grand Touring Low Beam Light Bulb
    By tefloncandi in forum Mazda5 Audio & Electronics
    Replies: 6
    Last Post: 03-22-2011, 11:13 PM
  4. Replace High beam headlight bulb
    By polypep in forum Mazda6 Audio & Electronics
    Replies: 2
    Last Post: 10-26-2009, 09:03 AM
  5. Help changing headlamp bulb (Bulb seating wire!!?!?)
    By Mark115 in forum Protege5 Lounge & Welcome Area
    Replies: 9
    Last Post: 03-13-2007, 11:37 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •