Gauge Panels

[TurfBurn]

Our 3x52mm gauge panels are in. They screw right into the stock mounting locations and will hold 3 52mm gauges. They are made out of heavy stainless material. You can paint them, or use them as is as they have a beautiful finish. I'll post pictures soon!

Let me know if you are interested... cost on these is only 45 dollars shipped!

[TurfBurn]

Here is a picture of the panel installed with one gauge in place... sorry the pic isn't better quality though!

http://www.msprotege.com/forum/attachment.php?attachmentid=37611

[atticus1398]

Nice, hows installation/fitment?
Any plans on one w/ tt hole? If not Ill take one of these on payday.

[TurfBurn]

Installation is easy as heck.. and fit is great. The first batch I have (what the picture is of), the holes are a little lower than they should be to center the gauges... hence they are discounted on cost... Otherwise panels will be 55-60 usually. I can do the one hole with the TT for people, but I'd want two confirmed buyers minimum before I do that run. I'm getting high on stock levels right now. I also have requests for one gauge with two TT slots (as the tt and EBC are the same size if you have Greddy's).

So let me know what you think and I can go from there!

Thanks,

Steve

[atticus1398]

Hmmm,
Ideally, 2 holes and a tt wold be great, but impossible. So if you have any of the three holers left on Fri, Ill take one. That third hole is gonna nag me to get a oil press gauge, i just know it.lol, or maybe a wideband... here we go again.
Pay pal?

[TurfBurn]

Are you sure that 2 holes won't fit? I'd have to take a set of measurements and see what i could do with it... but figured I'd double check with you. I don't have the width of the TT on this computer... so It's hard for me to double check.. but I could do that tonight if you wanted. Otherwise I should still have a panel for you. I can get you an autometer oil pressure gauge as well if you want one! :) Let me know what style you'd like and I can quote for you. I can usually match or best Summit Racing's prices... which is about the cheapest competitor I've found.

For a wideband I recommend the PLX M-300... from plxdevices.com. I don't selll the, but I use one and have been very happy with it, and they are a great price!

Thanks!

Steve

[atticus1398]

Ohhh, 2 gauges and a tt, Im in.
Estimated price when you get chance. GReddy tt.
Thanks Steve

PM sent

[TurfBurn]

I'll check and draft that one tonight... we'd need one more person that would be game for it (or you can buy two panels :) ), and then I can launch the run.

[atticus1398]

autocad?

[TurfBurn]

SolidWorks

[Rawyzf]

How about one with side by side slots for a TT and EBC, Greddy?

[TurfBurn]

I'm going to work out some new methods to do these panels. There are a lot of one off parts requests coming in... I think I'll be able to hold a fixed price for you guys of 62 dollars per one off part. I'll likely need to take deposits of 40% down on the design once it is completed, and then it will be submitted. That way I can be sure I don't get left with panels no one else needs, and you can get what you want.

If that sounds acceptable to you I'll start on the one off parts you guys are all after.

Thanks!

Steve

[Rawyzf]

Sure....sounds good to me. I'll pay in full up front if you would like.


-Ryan

[TurfBurn]

No need to... but that can be done... I'll try to get more panels drafted for you guys shortly... Then you can confirm it is the layout you want and we'll go from there...

Thanks!

Steev

[TurfBurn]

Lead times on the panels will be about 2 weeks... usually less... but figure 2 weeks.

[Rawyzf]

Sounds good.
Lead times on the panels will be about 2 weeks... usually less... but figure 2 weeks.

[atticus1398]

Sounds good. Let us know.
2 gauge and a GReddy tt.
Thanks Steve

[TurfBurn]

I can now do lower volumes for you guys on these panels than I originally thought. I'll notify if pricing changes. But if you want a panel made specifically for your desire and there are not multiple others after that panel, you can get one designed. Once that has been done, you put downa 50% deposit on the total cost of the panel (1 off designs will typically run about 60-65 dollars). And then once the panel is complete you'd pay the last half and I would ship out to you. So I will do single panels for you.

Steve
NSN Motorsports

[TurfBurn]

Found out the Greddy TT is wider than I had referenced initially. I can only fit 1 gauge next to it.. if you want auxillary switches or so forth I can do that!

Thanks,

Steve