Help, Stock pipes + Greddy Type S = Stalling

[mspeedpro]

Did the nice little how-to today with mp3moose and it looks to be a very nice clean install. When starting it up, stalling is bad. If I give it gas and blow it off, it drops way down and dies. Idling is a very strange thing: the tach surges to 1100ish and drops down almost to zero endlessly, up down, up down up down....
making it harder or softer seems to have almost no effect on it. Also, the bov appears to be 'half opened' under idle, is this right??

It came with an extra spring but when I was removing the little screws holding the bov together to look at spring, two of them were stripped. I was very careful with them and I don't know how they got stripped (doughpoke (scratch) . Any help would be appreciated.

IIDDEEAASS??

[mp3moose]

Yeah, not much luck here. It seems to be working fine and no leaks around, but the valve isn't closing fast enough to keep the car running. Best guess is the wrong spring, but we can't test that theory.

[mspeedpro]

as for vac source, its got a dedicated source that was recommended from 505 so that should not be an issue... argh sumone help-- im aggravtaed

[dominoy2k1]

so you cant tighten it all the way?

[mspeedpro]

ummm ya i can. it just has no effect, i have removing battery red term to reset ecu... will let u know whats its like in 5 mins

[mp3moose]

We got it tight as far as it would go on hard, but then tried all the way soft and inbetween several places an nothing.

[dominoy2k1]

hmm only thing i would suggest is adding a quarter/s inside the bov. i think igdrasil did it and it stopped his stalling and rough idle.

[mspeedpro]

ugh its pissing me off, it idles TERRIBLY when i turn it on, up down up down. the bov opens and closes opens and closes with the vac surging.... after a while it idles nice. but when i hit gas it falls back REAL low then does the little high-low dance again

[mp3moose]

If only we could get it open.

[mspeedpro]

whats a qyarter/s??

[dominoy2k1]

quarter, 25cent coin.

[Dexter]

lol

[mattybo]

are you venting this type-s? Or are you recirculating? Dual setup?

[mspeedpro]

i got the dual setup with stock bpv and greddy venting, followed mach 3.5 how-to precisely

[mofoaka]

gooooood lucckk

[Mr. Win]

i would suggest buying the recirc kit from protegegarage.com for 15bucks itll make it easier...

umm might. that or you bov could be not pushing all the way closed that what happened with my dsm one so i had to swap it out. is it a brand new piece?

[mspeedpro]

nah got it used. its really pissing me off. basically- if i tighten it all the way, turkey is there and idles fine: makes sense b/c bov is doing nothing. but just as soon as i hear any sound from BOV at all, I get stalling problems. I assume its not a leak b/c it runs fine with BOV under full HARD setting. Also, followed mach3.5 how-to but used a few differant supplies that looked to be as close as I could find and my fucking BOV keeps falling off.
project is becoming huge pain in the ass and to be honest im sort of embarrassed I even started it.

[mofoaka]

uMm.. dude i dunno what to tell you guy.. i dont' have that stall issue after i adjust my BOV to full hard setting. btw sorry about the phone deal, my gf's house has messed up reception.


nah got it used. its really pissing me off. basically- if i tighten it all the way, turkey is there and idles fine: makes sense b/c bov is doing nothing. but just as soon as i hear any sound from BOV at all, I get stalling problems. I assume its not a leak b/c it runs fine with BOV under full HARD setting. Also, followed mach3.5 how-to but used a few differant supplies that looked to be as close as I could find and my fucking BOV keeps falling off.
project is becoming huge pain in the ass and to be honest im sort of embarrassed I even started it.

[mspeedpro]

haha its ok... and just a foot note.... when it is in full soft setting i can rev it up and get a pretty loud WHOOSH sound but it will of course plumet to 0 and stall. However, like I said im getting a whoosh! this is not the typical greddy type s sound AT ALL. I saw and heard star 80s at stock boost and this is definitly not a TYPE S style sound. ugh i hate my msp at the moment.

[dominoy2k1]

duh, thats because the msp sucks....

[mspeedpro]

i seem to remember you searching for electrical tape b/c yo shiit wasnt working well for meet -=) hah

[dominoy2k1]

hmm i dunno what you are talking about...(shrug)

[mp3moose]

your sister is hot.

[dominoy2k1]

whos sister?

[mp3moose]

mspeedpro...unless you have a hot sister domino.

[dominoy2k1]

hmm well i am told the youngest of sisters is hot. hmm i need pics...lol. so you couldnt get the bov to work?

[mp3moose]

sweet!

Yeah, switched to the smaller spring and the valve stays closed at idol but doesn't open at all under load. This is all besides the fact that it wont stay attached.

[mspeedpro]

my sister is not attractive, ive never had a friend tell me that.
ya the motherfucker is pissing me off, im trying to get my hands on stock msp ic-> tb pipe

[dominoy2k1]

maurice might have em or 1fastmsp might have em. just get some hardpipes and get the greddy flange welded on.