Essential Speed Hard pipes

[markmurray77]

stage 1a-Hard pipe kit
-all intercooler piping re done in 304 ss polished
-includes all silicone couplings and gear clamps
-turbo smart b.o.v. and vacummun line
**piping availiable with ceramic coating(+200.00) powder coating(+150.00)**
cost of:$ 875.00 plus taxes and shipping
INSTALL TIME- 2HRS MAX.

stage 1b-Turbo cold air inlet piping
-2.5" 304ss piping polished: also availiable in ceramic & powder coating (extra price)
-includes filter kit locates filter to cold air in fender well.
-all silicone couplings and gear clamps
*location for vacummun and air temp sensor AND bracket to re-locate rad.reservoir
cost of: $ 300.00 plus taxes and shipping
INSTALL TIME-1.0 hr

http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/maf2.jpg
http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/maf.jpg
http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/pipes.jpg
http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/side.jpg

stage 2-frount mount intercooler
-* joins with stage 1a, to create extention piping for frount mount intercooler
-304 ss intercooler piping polished(ceramic & powder availiable)
-all silicone couplings and gear clamps
-radiator support bracket
-front mount intercooler(will support 15psi easily) show polish availiable.
-manual boost knob **suggested boost max. is 12psi**
cost of:$1200.00 plus shipping & taxes

http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/fmic.jpg
http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/bracket.jpg
http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/fmic2.jpg
http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/front.jpg
http://www.mazdamp3.com/vbb230/_handler.php/markmurray77/cutout.jpg


Prices are in Canadian

[2K3 MSP]

Just thought that I'd post another option. I believe these prices are all CAD

Hopefully they are...$875 for just hard pipes?? EIther way, that's a rip off...only the FMIC setup sounds worth it to me...But it says "joins with 1a" does that mean you have to buy both??
Where did you get that pricing from??

[markmurray77]

Prices are Canadian, and I think that he hard pipe kit comes with a BOV upgrade not just the flange. Looks like a pretty good deal to me.

[jeremyfl]

Dude pricing in CAD that isnt very much in USD then???

[jeremyfl]

Nevermind did the conversion thats like $629.22 that is expensive....

[t3ase]

Instead of bitching about pricing, we've got to realize that we finally have parts for our cars. I'm sure we all realize we don't have much aftermarket support right now, so everyone that helps out, regardless of cost, helps our community out enormously.

If you can't do it, don't buy it. Just say "Thanks" to whoever it is who posts the parts. At least we can show support instead of this negative streak we have going right now.

[boostisgood]

Pics, and type of IC would help sell for this company. Anyone got em ?

[2K3 MSP]

I'm only being negative because we already have companies doing hard pipe kits for half of that price...And I did say that the FMIC set up sounded like a good deal unless it was only the FMIC and you still needed to buy the hard pipe kit. The description wasn't worded the best...

[markmurray77]

It does come with a BOV and I know that they are a Spearco dealer so assume a Spearco FMIC. Theres a boost controller too. I'll see if I can get some pics from them

[122 Vega]

You have to save them to a source outside Hotmail for us to see them...

Britt

[markmurray77]

updated the original post with pictures.

[SuperSpud]

yeah, spools are $400... and I"ve seen others for $275

[ping]

GREAT pics - hey, while you had it apart did you upgrade the OE wimpy horn? Looks like a well done kit - thanks for posting it. Someday... someday...

[YuYuRena]

what's that last picture about?? I'm confused about that picture?? Does that mean you have to cut something out of the car. Also I notice you installed this on a titanium MSP, how does the CAI sticks out in the "duct," is it visible? And that route from compressor discharge to the IC intake is long and "windy" woW!!! How much pressure drop?? How about core efficiency?? What is the angle of endcap, especially on the intake side?? Is it greater than 13 degrees??

Sorry about all these numbers just wanna know so I can do some calculations

[YuYuRena]

Oh and good job on trying to make the MSP better, I salute you!!

[boostisgood]

DooD, I salute you on your efforts. But that IC is mighty small, and does not look like the endcaps are created with the airflow efficiency in mind.

Just my0.02 :D

[BremertonMSP]

It does look like a nice kit, but I'm not sold on Blow Off Valves. I would rather use a Bypass Valve. The reason being, with a BOV, you release metered air to the atmosphere. With a BPV, the metered air stays in the loop, so you have the correct AFR.

I know some of you guys won't agree, and that's fine. I just feel better keeping the system intact.

[markmurray77]

I think most people prefer a BOV over a BPV, thats probably why they went with that. I also believe that that intercooler can flow over 300 hp

[DiscreetSpeed]

you guys need to check this place out, spoke to kevin, the owner,
and this guys really getting into the msp. and the prices are great! im gonna get these hard pipes as i dont want to do a front mount.(sleeper....)

[RAAZ227]

Nice pics! Not sure about the price. A nice (larger) i/c here in the states with a decent set of end caps will go for $900.00.


:D