FS: MAM Thumper Turbo kit w/ GT30R

[ddogg777]

Huge debt from gradschool and a baby on the wheel = selling aftermarket stuff.

The last thing this kit did was pound out a 12.0s quarter mile, 400+ hp, and a snapped axle at 18psi. The coated turbo functions well; I blew into the exhaust inlet and the turbines spun very well--I didn't expect it to be so smoothe. There doesn't seem to be any more shaft play than new. The turbo kit was used for about 4000 miles, more than half highway miles from AZ to UT and the other tuning and a little track time.

The ugly:
The whole kit is dirty because I haven't done anything to the car this winter except start it up on weekends. I don't have time to clean it up for you, perhaps price will reflect that.
The wastegate is a used Turbonetics--scratched but works well.
The blowoff valve is a Tial. It's dirty but will clean up very nice.
The intercooler is huge and you will need to trim some sheet metal off the bumper (only took a few minutes to do it and doesn't cut into the meat of the bumper), very good condition with only a few slight fin bends from bugs.
The cold pipes are filthy and have paint scratches where it rubbed the car (you're supposed to put silicone on the frame edges, I failed to do that). The smallest pipe (s-shape) pipe has a dent in it (not a bend) from loading the car onto a trailer. I never liked that pipe anyway; it's the driver's side end that couples the intercooler and should be .5" longer for a nicer fit. I will leave the GM air sensor attached with pigtail.
The manifold has a few spots where the ceramic coating is flaking. I needed to get ARP stainless headstuds to bolt it on, those will be included.
The 3" downpipe uses a v-band, is ceramic-coated, and has a nice area in the back where oil dripped on it from a loose oil line and cooked (will need steel wool). I am parting all the pieces out. Everything can be bought separate except for the cold pipes, they all go together.
Coated Turbo with v-band exhaust outlet (cost me additional $150): sold
Pipes and intercooler: SOLD! (Nice Tial valve available for $100)
MAM tubular manifold with T3 flange: sold

[Focus]

If you part the kit out, I would be interested in the Turbo !!

[ddogg777]

I will part out the kit if everything can be spoken for at reasonable prices. I know that yashart wants the manifold and crazycaker wants my downpipe.

[ddogg777]

This part of the bumper needs to be cut. It is not noticeable and on the bright side, your huge IC will take its place... :)

[khaosman]

This part of the bumper needs to be cut. It is not noticeable and on the bright side, your huge IC will take its place... :)

You must have a mean saw to do that :eek: Well, better than a jig-saw at least lol

Good seller... good stuff there.

[CrazyCaker]

I will part out the kit if everything can be spoken for at reasonable prices. I know that yashart wants the manifold and crazycaker wants my downpipe.

Consider the dp sold to me if you part it out. :)

[Blackrose]

You must have a mean saw to do that :eek: Well, better than a jig-saw at least lol

Good seller... good stuff there.

Its called a plasma cutter my friend. Well thats how i did mine.

[ddogg777]

The kit was on for about 4000miles according to post #1.

[ddogg777]

Its called a plasma cutter my friend. Well thats how i did mine.

It can be done with a handheld reciprocating saw.

BTW, I just took off my 626 manifold, get ready for it too!

[Blackrose]

It can be done with a handheld reciprocating saw.

BTW, I just took off my 626 manifold, get ready for it too!

How much for mani?

[ddogg777]

Dunno, what's the cheapest it's gone for here?

[SeR_Cyclops]

same on mani price?

[sandspeed]

Damn thats some nice stuff. Someone should pick this up before its gone...

[dave45090]

What would this kit be like on stock internals.....a ticking time bomb? Can you run this kit at 7 psi or is that pointless?

[nvmsp]

i want that manifold so bad, no money though.(bang)

[Maxx Mazda]

Was your car pictured on the MAM site? I don't know of any other kits with the yellow piping...

[Focus]

Dunno, what's the cheapest it's gone for here?

I paid $750 for mine...

[ddogg777]

I paid $750 for mine...

I think he was talking about the 626 mani... :)

[ddogg777]

What would this kit be like on stock internals.....a ticking time bomb? Can you run this kit at 7 psi or is that pointless?

You can but you'd be better off with a smaller turbo that spools faster. Or you can buy my car that already has a built engine/tranny. :)

[yashart_mp3]

I'm praying that you part out the kit... I really want that turbo mani :)

[CrazyCaker]

^ same here, I REALLY need that downpipe. :)

[ddogg777]

Yashart gave me a good offer on the maifold, send me an offer for the DP and I will go ahead with the parting out...

[ddogg777]

I'm officially selling the parts separate. The tubular manifold and downpipe are spoken for. Be sure to check out my other stuff in my sig..

[Focus]

I'm officially selling the parts separate. The tubular manifold and downpipe are spoken for. Be sure to check out my other stuff in my sig..

Don't forget about me...Very interested in the Turbo!!

[ddogg777]

What's good? $700 for the turbo and $300 for the IC and pipes (minus blow-off valve, $400 with tial valve)

[supa saiyan pr5]

U sir have PM

Jeremy

[ddogg777]

I have a good offer for the manifold and will sell it by next Wednesday unless someone is willing to pay $650 before then.

[ddogg777]

Okay, tubular manifold is spoken for...:)

[03spicyspeed]

how does the gm air sensor work?

[igdrasil]

If Focus dont take the turbo, Im in!
The downside on my deal is I can only do it in 2 payments

[ddogg777]

The GM solenoid is a PWM solenoid that can be controlled by standalone computers like the AEM that I had. It's cheap, like under $50 for solenoid and pigtail

[ddogg777]

If Focus dont take the turbo, Im in!
The downside on my deal is I can only do it in 2 payments
You're 3rd in line.

[03spicyspeed]

can i use this IC setup and the tail valve with my stock maf and turbo

[ddogg777]

The turbo outlet pipe will have to be changed for the mazdaspeeds and then you would have to cut one of the pipes and put the maf inline with it. This setup was meant for speed density.

[MrDiggler]

Keep me in mind as well on that turbo. It's a little more than I need, but that hasn't stopped me in the past. PM me if you can't find a buyer.

[ddogg777]

Turbo sold.

[CrazyCaker]

Downpipe sold.

Payment sent, thanks Duane!

[ddogg777]

Thank you!

[ddogg777]

Tubular manifold is still for sale as I haven't heard back from my buyer. Yashart, if you've gotten the money together it's yours.

[ctt 1982]

someone buy this sexy mani already. they look even better in person

[mryellermp5]

You should know, LOL...and i do TOO hehe
someone buy this sexy mani already. they look even better in person

[Matthew1785]

I'd buy the T3 mani but 650.00 is a little to steep for me

sorry

[Blake]

id fuckin love to have that mani.

[ddogg777]

bump

[ddogg777]

Price a little lower and I've washed up the pipes. The Tial valve looks nicer too.

[prose92]

im interessed for the ic kit.... but a get some question. can you tell me if it can be a bolt-on kit with my stock msp... did he pass like the kinetic by cuttin some fram part.....

[yashart_mp3]

PM sent

[yashart_mp3]

Payment sent ;)

[ddogg777]

Tubular manifold is sold!

@prose92, I don't have an MSP. I have been told that the only difference between MAM's msp kit is the single pipe coming off of the turbo.

[StealthWyvern]

Payment sent for Ic setup minus tail valve.

[StealthWyvern]

Ddogg77 whats all left that you have to sale?

[dannyboy17]

gonna sell the 626 manifold anytime soon?

[ddogg777]

626 mani was sold...

I have my FI Evo hood, stainless still hood prop kit, AEM 3.5 bar sensor, MAM boost block, 110gph external fuel pump, MAM fuel rail, center console with touchscreen. After I fix up the car, it will be sold as stock but will still have the forged motor, welded LSD, tokico suspension.

[StealthWyvern]

Thanks ddogg777 I some what received my ic setup today by that I mean that UPS are a bunch of freaking retards who can verify a address properly. This makes the 8th package in a row literally from them that they can't even delver the crap to the right house. Fedex, DHL, and USPS can get my house right! I’ll go pick it up from my neighbor’s house tomorrow morning and give a update on the tread. Luckily for me my neighbor is 70 some odd years old and has no idea what he received in the mail.

[StealthWyvern]

Update:

I recieved the ic setup. It was well packaged and arrived in excelent condition! THanks again ddogg77!