Spool Stage 2 FMIC Installed *Pics*

[Boosted Orange]

Well over this weekend I had my Spool Stage 2 FMIC installed on the MSP. It was origonally made for an MP3 turbo upgrade over the Stage 1, so it took a little work to get it in and set.

The cold pipe was a direct replacement fit, but the hot pipe was something that needed lots and lots of work. I only have one quick shot from the front for now until weds when I can get some under the hood shots.

http://www.tmobilepictures.com/photos/photo09/60/e9/641eb0370d1f.jpg?_rh=1ut5e03gjn4fb1fb3vywmffzc

Lemme know wacha think!

~ Nick ~

[RenzoMSP]

Looks good. How does the car perform?

[Boosted Orange]

Incredible!!!!!

Well lets put it this way, I ran side by side with a SRT-4 with a stage 1 from a 35 mph roll.

[Mr. Win]

you didnt end up going with the starion?

[Boosted Orange]

nope

[Mr. Win]

nice well good choice... im glad you like it. Looks good too.

[RenzoMSP]

Are you gonna put in your grill or leave it open?

[Boosted Orange]

What do you guys think will look best? I wanted to leave my grill off and remove those tabs, but what do u think will look better?

[slug420]

black wings west mesh looks best to me....but then again, im biased...

[Boosted Orange]

I like it wide open, and Im also removing the license plate, so it'll look crazy when Im coming up behind someone.

[Hypnotized]

Looks good bro. Leave the grille off. It looks better IMO.

[low_psi]

if you leave the grille off you can just paint the tabs black and they are hardly noticable. that's what i did with my top tabs since I want the option of putting the grille back in place.

[jeffmsp]

be careful, some motha f**** tried to rip out my fmic and i have the stock grill in place lol bastard ripped out my splash guards from underneither, but stopped when he realized it was bolted in, fing people/

btw welcome to the fmic club. you are now better than a normal person :)

[Boosted Orange]

LOL dont worry unless they have a grinder it not coming out....its welded in there...

[Boosted Orange]

and plus its too damn big to take out unless you remove the entire front end...hahaha

[Hypnotized]

You welded the fmic?? I cant believe someone would actually try to rip an IC off a car. What good would it do them? Some fuckin people just dont make sense. By the way, did you have to cut anything to fit that IC? It looks allot bigger than mine. What kind of BOV are you running?

[Boosted Orange]

Yes I had to remove the center section of the bumper support bar and I am running the new Greddy Type RS BOV. Atmospheric set-up with no recirculation and there are no stalling problems at all.

[Hypnotized]

Sweet show me some pics of the engine bay. PM me if you can or post them on this thread.

[SpeedBeaver]

Where can you buy this kit?

[igdrasil]

did you had to remove your bumper?

[CChris704]

hows the RS, i think i'm going to go that.... and have you heard a type-s cause thats what i used to have.

FMIC looks awesome

[vindication]

looks nice, but that endtank design doesn't look to effecient. you should get those endtanks redone.

[Boosted Orange]

I wish I had the Type S BOV but they dont make it anymore. I would be more than willing to do a trade for a Type S. The RS is loud when it hits, but it hits pretty inconsistantly since Im only running on 6psi right now cause I dont have all silicone and the rubber ones arnt that great.

[orlandomsp]

How much was it?

[Boosted Orange]

I got it off another member for a total of $218 shipped.....not bad!!!!!!